DIY Tub Installation.
DIY Tub Installation.
Blog Article
The article which follows about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is exceedingly fascinating. Check it out yourself and decide what you think of it.
Setting up a tub isn't specifically brain surgery, yet it does require solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old tub with a new one is likewise a reasonably hard project. If the old tub is readily easily accessible, the task can relocate speedily; if you have to open a wall to eliminate the old tub as well as place the brand-new bath tub, the job is much harder. In either instance, the job is within a house handyman's skills, although you will certainly require an assistant to move out the old tub and set in the new one. Ensure you have qualified yourself for the job as well as are comfortable attempting it. Instead of employing a specialist to take over a halfway-completed project, it is better to think about employing one before you begin. Chances are you may require a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new tub in your restroom if you have already bought a new bathtub and also do not require to alter the arrangement of your previous water supply pipelines.
Your devices as well as material checklist should comprise the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, after that the first thing you need to do is detach the supply of water. After doing so, turn on the taps to drain pipes any type of water staying in the system. The process of getting rid of the existing faucets can be quite problematic as a result of the limited access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will come from the pipelines. When the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to moving on to fit the brand-new taps, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic port to stop damage to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin ensuring that the washers remain in place in between the faucet and the sink. Safeguard the tap in place with the supplier offered backnut. When the faucet is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous type ought to be attached to the faucet ends initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Tub
Making use of both wooden boards under its feet, put the bath tub in the called for position. The wooden boards are practical in equally spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four little factors.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the bath tub until the spirit level checks out level.
To set up faucets, fit all-time low of the outermost flexible tap connector to the suitable supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Switch on the water supply and inspect all joints as well as new pipework for leakages as well as tighten them if needed. Load the bath tub as well as additionally examine the overflow electrical outlet and the normal outlet for leaks.
Finally, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub should wait until the bathtub has actually been made use of at the very least when as this will certainly resolve it right into its final setting.
Getting ready for the Installation
Firstly, the sustaining structure provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the adaptable faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last setting.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is required to seal the joins with a silicone rubber caulking. This is important as the installation can move enough to break an inflexible seal, triggering the water to pass through the wall in between the bath as well as the tiling, leading to issues with dampness and possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components as well as installations. They are sold in tubes and also cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to securing, to permit the movement experienced when the tub is in usage. The sealant can break rather early if you do not take into consideration this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or water resistant glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our post about Tools You Need to Install a New Bathtub . Thanks for finding the time to read our piece of content. Sharing is caring. You just don't know, you may very well be doing someone a favor. Thanks for taking the time to read it.
Schedule Service Now Report this page